Guide
UPC barcodes for small sellers: what you need first
A UPC is two things: a number that belongs to your business, and a picture of that number in bars. Any good tool can draw the bars. The number has to come first.
Updated
A UPC number and a barcode are not the same thing
The 12 digits under a UPC barcode are a product number (GS1 calls it a GTIN). The bars above them are just that number drawn so a scanner can read it. Shops, marketplaces and distributors care about the number: whose it is, and which product it stands for.
EncodeLabel doesn’t issue UPC numbers. It turns a number you already have into a barcode and checks its last digit. It doesn’t sell or register numbers, and it isn’t connected with GS1.
So the order is: get your numbers, give each product its own, keep a list of which number is which, and only then print barcodes.
Where the numbers come from: GS1
In the United States, GS1 US issues them. Its page on getting barcodes describes two ways (GS1 US: How to get UPC barcodes for products):
- A GS1 Company Prefix, which lets a business make many numbers of its own. GS1 US recommends it for companies with growing product lines.
- A single GS1 US GTIN, one number at a time, which GS1 US suggests may cost less for a business with only a few products.
Prices and terms are on GS1 US’s own pages and change from time to time, so check them there.
Why a number bought elsewhere can fail
Some marketplaces check numbers against GS1’s records. GS1 US quotes Amazon® Seller Central: “We verify the authenticity of product UPCs by checking the GS1 database”. It lists “The GTIN is not licensed to the brand owner” among the reasons Amazon may reject a UPC, and warns that a seller who gets this wrong may have their account suspended or have to relabel their products (GS1 US: barcodes for Amazon).
Before you buy a number from anyone other than GS1, look its company prefix up in the GS1 US database, which shows which company licensed it. If that isn’t your business, ask the shop or marketplace you sell through whether it will accept the number.
Labeling your own stockroom, shelves or equipment? Then you don’t need GS1 at all: any number works, and a Code 128 or a QR code usually fits the job better than a UPC.
The check digit
The 12th digit of a UPC-A is a check digit, worked out from the first 11. It lets a scanner notice a misread, and it lets you notice a typing mistake. This is how it is worked out, with 01234567890 as the first 11 digits:
Add the digits in the odd places
The 1st, 3rd, 5th, 7th, 9th and 11th digits: 0 + 2 + 4 + 6 + 8 + 0 = 20.
Multiply by 3
20 × 3 = 60.
Add the digits in the even places
The 2nd, 4th, 6th, 8th and 10th: 1 + 3 + 5 + 7 + 9 = 25. With the 60, that makes 85.
Round up to the next ten
The next ten after 85 is 90, and 90 − 85 = 5. The check digit is 5, so the whole number is 012345678905. (A total that is already a round ten gives 0.)
You don’t have to do it by hand. On the UPC-A barcode page or in the quick label tool, type the first 11 digits and the check digit is added; type all 12 and you are told if the last one doesn’t match. That shows a number was mistyped, but not which digit is wrong.
GS1 US’s own advice is never to alter a barcode or add or delete any of the numbers below it (GS1 US: Barcode FAQs).
UPC-A or EAN-13?
They are the same system. UPC-A has 12 digits and is used mainly in the United States and Canada; EAN-13 has 13 digits and is used in most other countries. A UPC-A with a 0 in front is a valid EAN-13: 012345678905 and 0012345678905 are the same number.
Use the one your numbers were issued as, and the one your shop or marketplace asks for. Both are drawn by the site, each with its check digit worked out: UPC-A and EAN-13.
Print size and colors
A UPC-A has a standard size, called 100%, with its narrowest bar 0.33 mm wide. The retail range usually stated is 80% to 200% of that. These widths include the blank margin at each end, which is part of the barcode:
| Size | Narrowest bar | Width with margins |
|---|---|---|
| 80% (smallest) | 0.264 mm | 29.8 mm (1.17 in) |
| 100% (standard) | 0.33 mm | 37.3 mm (1.47 in) |
| 200% (largest) | 0.66 mm | 74.6 mm (2.94 in) |
That decides the label. Measured with the site’s own layout for a single barcode:
- On a 1 × 1 in label a UPC-A comes out at about 64%, below the retail range. Handheld scanners often read it; a shop’s checkout scanner may not. The tool says so on every label.
- On 1½ × 1½ in labels it comes out at about 96%.
- On 1¼ × 1¾ in labels, 32 per sheet and on 1 × 2⅝ in labels it reaches 100% or more.
- Dark bars on a light background. Black on white is best. Red, orange and yellow bars usually can’t be read, because most scanners see by red light.
- Don’t stretch, squash or crop it. GS1 US warns not to cut off or shrink barcodes.
- Mind the printer. A small UPC needs a sharp printer. On a 203 dpi thermal printer every bar is a whole number of dots, so a UPC-A there is either about 28 mm wide (76%, under the retail minimum) or about 42 mm (114%), with nothing in between.
More on sizes for every kind of barcode in Barcode and QR code sizes.
Print the barcodes
Once you have your numbers:
One product
Type the number on the UPC-A page or in the quick label tool, pick your label paper and fill a sheet.
Many products
Keep a spreadsheet with a column for the UPC, the product name, size or color, and how many stickers each needs. In the designer, add it with Add a datalist, choose the UPC product sticker layout, and print with Use a quantity column.
Before the batch
Print one sheet, scan a few stickers, and check each scan gives the number in your list.
When a spreadsheet has turned a UPC into 3.6E+10 or dropped its first zero, the site puts the zero back where the check digit proves it, and points out numbers it can’t trust. Format the UPC column as Text in your spreadsheet to stop it happening.
Try it
Free for up to 100 labels a month. No account needed. Your labels are made in your browser.
Amazon is a trademark of its owner. EncodeLabel isn’t connected with or endorsed by Amazon.