Guide

Cable and wire labels: flags and wraps

Labels for network, power, audio and video cables: a flag that folds around the cable and reads from both sides, or a wrap with the words repeated all the way around.

Updated

Make cable labels

Two kinds of cable label

A label at each end of a cable says what it is and where it goes. The label designer has two layouts for it:

LayoutHow it goes onSuits
Cable flag labelThe blank middle goes around the cable and the ends stick together, back to back, so the words show on both sides.Two lines of words, cables in a bundle
Cable wrap labelThe whole label goes around the cable, the words repeated along it, so one copy faces you from any side.Short codes, where a flag would get in the way
Above, cable flags on 1 by 2⅝ inch labels: each label has a cable code and where it goes, such as SW1-01 and Desk 1, at both its left and right ends, with short fold marks at the edges of the blank middle, two labels for each cable. Below, wrap labels on 1 by 2 inch labels, each with its cable code eight times, turned to read along the cable
Cable flags on 1 × 2⅝ in labels and wraps on 1 × 2 in labels, two of each for the first three cables of the made-up list further down this page.

Make cable flags

  1. Start the layout

    The button below opens the designer with the Cable flag label layout on 1 × 2⅝ inch labels, 30 per sheet. A label you were working on stays one Undo away.

  2. Type your words

    Pick the words at one end and type yours in its Text box; press Enter for a second line, such as where the cable goes. The first line prints in bold. Then do the same at the other end: the two ends are separate boxes.

  3. Print

    Open Print. On a sheet, A set number of labels prints just a few, and Start at lets you tap the first unused label.

  4. Put it on

    Peel the label and lay the cable across the blank middle. Wrap the middle around it and press the two ends together, sticky side to sticky side. With the cable running up and down, both sides read the right way up.

Make cable flags Open the designer

Four short marks at the edges show where the label folds; to leave them out, pick each one and press Delete.

For a cable that runs level, the flag can hang instead: under Label, set Orientation to Vertical, then choose Layouts and Cable flag label again. Its top half then prints upside down, so the hanging flag reads the right way up on both sides.

Make wrap-around labels

The Cable wrap label layout repeats the words along the label’s length, the part that goes around, each copy turned to read along the cable. The copies are about 6 mm (¼ in) apart: 4 on a 1 inch label, 7 on a 1¾ inch one. Keep the words short: they run across the label’s narrow side, only ½ inch on a 1 × ½ inch label.

Each copy is its own text box, so a short list is the quickest way to fill them all, even for one cable:

  1. Start the layout

    The button below opens the designer with the layout on ½ × 1¾ inch labels, 80 per sheet.

  2. Type a list

    Choose Add a datalist. In the box for pasted rows, type Cable on the first line, then each cable’s words on a line of their own, and press Use these rows. Check that First row is a header is on, then press Use 3 rows (it counts your cables).

  3. Check the labels

    Until you change the label, the layout fills itself in, every copy from your Cable column. Step through the cables with the arrows under the label.

  4. Print

    Open Print and choose Every row of your datalist. Set Copies of each row to 2 for a label at each end of each cable.

  5. Put it on

    Lay the cable on the label so it runs the same way as the words, stick down one end and wind the rest around.

Make wrap labels On a 1 × ½ in roll

To change the words by hand instead, pick each copy in turn and change its Text.

Thicker cables

A flag’s middle, and a wrap’s whole length, must go once around the cable: a little over 3 times its thickness (π times). Measure your cable first; for wraps, the table under Label paper has the figures.

The flag layout leaves a middle about 19 mm (¾ in) wide, for a cable about 6 mm (¼ in) thick. The middle is never more than a third of the label, so a short flag suits a thinner cable.

There is no setting for the thickness. To widen the middle, make the words at each end narrower from the side facing the middle: pick them and drag a corner on that side straight toward the end, or lower Width under Position and size (for the right-hand end, raise Left by as much; on a Vertical flag, Height and Top). The words shrink to fit. Then move the fold marks to the new edges of the middle, or delete them. A 10 mm cable needs a middle of about 31 mm (1¼ in), so start on a longer label, such as 1 × 4 in.

A label for every cable, from a list

Keep your cables in a spreadsheet, one row per cable. Both layouts take their words from a column called Cable (or Cable ID, Cable name, Label, Wire or Port), and without any of those, Name:

CableGoes to
SW1-01Desk 1
SW1-02Desk 2
SW1-03Printer
SW1-04Meeting room TV
  1. Add the list

    Start a layout, choose Add a datalist and open your Excel or CSV file, or paste the rows, with First row is a header on. Until you change the label, the layout fills itself in from the Cable column; if you’ve changed it, choose Layouts and the layout again.

  2. A second line

    On a flag, pick one end, click after the field in its Text box, press Enter and choose Goes to under Insert a field. Then the same at the other end.

  3. Check the labels

    Check every row draws every label and lists any that need a look, such as words too long for their box.

  4. Print both ends

    Open Print, choose Every row of your datalist and set Copies of each row to 2.

Your list is read in your browser and isn’t sent anywhere to make the labels.

Numbered cables

Without a list, a flag can number itself: SW1-{{#|00}} at both ends prints SW1-01 on the first label and SW1-12 on the twelfth, but the two flags of one cable would then differ. For matching pairs, let the spreadsheet count: this formula in row 2, filled down, gives SW1-01, SW1-02 and so on, and Copies of each row prints each twice.

="SW1-"&TEXT(ROW()-1,"00")

Other number forms are in Dates, prices and numbers in fields.

Label paper

Any label paper works; for a flag, a long, narrow one leaves room for the words at both ends:

PaperSizePer sheet
Address labels, compatible with Avery® 51601 × 2⅝ in30
Address labels, compatible with Avery® 51611 × 4 in20
ID labels, compatible with Avery® 6577⅝ × 3 in32
Mini address labels, compatible with Avery® L765138.1 × 21.2 mm65 (A4)
Barcode label roll for a thermal printer3 × 1 inA roll, one at a time
Standard address labels, compatible with Brother® DK-120129 × 90 mmA roll
Address labels, compatible with DYMO® 302521⅛ × 3½ inA roll

Flags on 1 × 2⅝ in labels Flags on 1 × 4 in labels Flags on a 3 × 1 in roll

For a wrap, the label’s length sets how thick a cable it goes once around:

PaperSizeCable up to
Return address labels, compatible with Avery® 5167½ × 1¾ in, 80 per sheet14 mm (0.56 in)
Rectangle labels, compatible with OnlineLabels OL19301 × ½ in, 160 per sheet8 mm (0.32 in)
Rectangle labels, compatible with Avery® 942201 × 2 in, 24 per sheet16 mm (0.64 in)
Mini / slide labels, compatible with Avery® L765646 × 11.1 mm, 84 per A4 sheet14.6 mm (0.58 in)
Small barcode label roll for a thermal printer1 × ½ in, a roll8 mm (0.32 in)
Multi-purpose labels, compatible with Brother® DK-120417 × 54 mm, a roll17 mm (0.68 in)

Wraps on ½ × 1¾ in labels Wraps on a 1 × ½ in roll Wraps on A4 (84 per sheet)

Labels that stay on

Ordinary paper labels may lift off a cable. Self-laminating wire-marker labels are made for cables: as you wrap one, a clear part of the label covers the printing. They aren’t in EncodeLabel’s paper list, so measure one and type in its size: open Label, press Change under Label paper and choose Custom size.

For cables that get hot, oily or wet, or run outdoors, look for labels sold for that use and your kind of printer: EncodeLabel can’t tell you which will last. Direct thermal labels are sensitive to heat and light (direct thermal or thermal transfer).

Test before you print the batch

Test one label on your cable before you print the batch. Print one on the label paper you’ll use, put it on and look again the next day: the words should read the right way, a flag’s ends should meet and a wrap should go all the way around.

Before the first real sheet, open Print, then Line it up, and choose Print a test page. Print it on plain paper and hold it against a sheet of labels, up to a window. It never counts toward your labels.

EncodeLabel prints the words you choose. Which cables need a label, and what it must say or be made of, is for the rules where you work, your client or the equipment’s maker to say. This guide isn’t electrical or safety advice.

Try it

Free for up to 100 labels a month. No account needed. Your labels are made in your browser.

Make cable labels Printing help

Feedback

Suggestions and feedback

What would make EncodeLabel better, or what isn’t working? It goes straight to the people who run the site.

Only if you’d like a reply.

We use your email only to reply to you. Please don’t include passwords or private details. Privacy Policy

Add EncodeLabel to your Home Screen

One tap to your labels, like an app, with nothing to download from an app store.